14" MISSOURI


























modifications available upon request

Minimum Depth: 6' (1.83 m)
Maximum Depth: 44' (13.41 m)

Estimated General Measurements:
Length: 102' (31.09 m)
Width: 21’-6” (6.55 m)
Estimated Dry Weight: 208,000 lbs (94347.21 kg)
Hull Depth: 5’ (1.52 m)
Estimated Mean Draft: TBD
Ladder Length: 55’ (16.76 m)

Hull: (Approximate Sizes)
Center Section: 36’x 11’-6” x 5’
Side Pontoons (overall): 88’ x 5’x 5’
Overall Size: 88 x 21’-6 ” x 5’
Hull Skin Thickness: ¼” (.635 cm)
Watertight Bulkheads: Approximately every 10' (3.05 m)
Testing: Every section of floatation is pressure tested for leaks before paint

Paint: (Fabricated Items)
Hull
Prep: Commercial Blast
Sides and bottom paint: Coal Tar Epoxy (Black)
Top: Mastic Epoxy with grit added (Grey)

Cab/ Enclosures/ Other
Prep: Commercial Blast or Phosphate wash
Primer: epoxy primer
Paint: Polyurethane

Dredge Pump:
Pearce 16 x 14 x 40
16” suction (40.64 cm)
14” discharge (35.56 cm)
40” diameter Impeller (101.6 cm)

  

Engine and Transmission:
Engine: C-27ACERT 875 hp C rated (652.49 Kw)
Power Trans: Twindisc Marine Transmission
Fuel Capacity: 2000 gal (7570.82 L) shared

Auxiliary:
Manufacturer: C-11 ACERT 420hp D Rated (313.19 Kw)
Power Trans: Funk Hydraulic Drive
Fuel Capacity: 2000 gal (7570.82 L) shared

Fresh Water Service Pump:
Pioneer, Berekeley or equal

Cutter Type and Specifications:
Cutter Type: Cutterhead
Size: 43” ID (109.22 cm)
Drive: SAI hydraulic Planetary Drive
Speed: 0-25 rpm
HP:150 (111.86 Kw)

Winches:

Swing: Pullmaster H- 12,000lbs (5443.11 kg)
cap bare drum
Ladder: Pullmaster M-18 18,000lbs (8164.66 kg)
cap bare drum
Spuds: Pullmaster H-12 12,000lbs (5443.11 kg)
cap bare drum

Spuds:
Diameter: 16” (40.64 cm)
Length: 55’ (16.76 m)
Wall thickness: ½” (1.27 cm)

Hydraulic Systems:
Winch system
Tank:160 gallons (605.67 L) shared (equipped with high temp/low level shutoffs)
Valves: Electro-Proportional
Pumps: Geartek gear pump
Motors: Pullmaster Motor
Contamination Protection: Pre-strainers, and 10 Micron (.01 mm) Filters
System relief: All circuits set at 2500psi (172.37 BAR)

Fresh Water Pump
Tank: 160 gallons (605.67 L) shared (equipped with high temp/low level shutoffs)
Valves: No valve variable displacement pump
Pumps: Oilgear variable displacement
Motors: Sun-Fab bent axis motor
Contamination Protection: Pre-strainers, and 10 Micron (.01 mm) Filters
System relief: All circuits set at 2500psi (172.37 BAR)

Cutter head
Tank:160 gallons (605.67 L) NOT SHARED (equipped with high temp/low level shutoffs)
Valves: Electro-Proportional
Pumps: Hydrostatic Transmission
Motors: SAI radial piston
Contamination Protection: Pre-strainers, and 10 Micron (.01 mm) Filters
System relief: All circuits set at 3200psi (220.63 BAR)

EVERY EFFORT IS MADE TO ENSURE THAT ALL STEEL HYDRAULIC LINES HAVE WELDED FITTINGS

Operator Cab
Standard operator cab 6’x8’ (1.83 m x 2.44 m) air-conditioned
Standard light package utilizes both 12 and 24 volt

   

110v/220v single electrical system:

24KW Generator belt driven by C-11
Cab AC and Heat

Instruments and Controls:
All hydraulic controls are electric joystick switch or pushbutton control
4” (10.16 cm) discharge pressure gauge 0-160psi 1pc
4” (10.16 cm) hydraulic pressure gauge 0-5000psi 4pcs
4” (10.16 cm) packing pressure gauge 0-160psi 1pc
4” (10.16 cm) Vacuum gauge
2” (5.08 cm) temp gauges hydraulic oil 2pcs

Miscellaneous Items:
Manual
2-ton (1814.37 kg) jib crane for pump service
Ladder sheave blocks
Swing winch snatch blocks
Chain handrail
Guarding
Fair lead
Suction Sleeve
Fire Extinguisher x2